We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.
In an article recently published in the journal Additive Manufacturing, researchers discussed the utility of ceramic heat exchangers made by binder jet additive manufacturing for concentrating applications of solar power with thermal energy storage in the molten chlorides.
Study: Binder Jet Additive Manufacturing of Ceramic Heat Exchangers for Concentrating Solar Power Applications with Thermal Energy Storage in Molten Chlorides. Image Credit: shmai/Shutterstock.com
The possibility for dispatchable energy on-demand using thermal energy storage (TES) and a conventional heat engine distinguishes concentrating sun power (CSP) from other renewable energy sources. However, in order to reach a competitive levelized cost of energy (LCOE), CSP system costs must be reduced.
A recent study of several triply periodic minimal surfaces (TPMS) and periodic nodal surfaces as heat exchangers revealed that the Schwarz-D TPMS surface has exceptional heat transfer performance. Group IV-VI transition metal carbides, borides, and composites are the most common ultra-high temperature ceramic (UHTC) materials. Prior to the introduction of additive manufacturing, TPMS devices were difficult to build.
Binder jet additive manufacturing, in contrast to previous methods for fabricating ceramic TPMS structures, is developing as a promising and scalable ceramic forming approach. Binder jet printing has been used to create UHTC heat exchanger plates in combination with reactive infiltration, but it has not yet been used to fabricate UHTC TPMS structures that are sintered to high relative densities. Lessons learned from sintering nanomaterials show that low green densities from forming procedures aren't always a concern and that achieving good uniformity is more significant.
In this study, the authors demonstrated the feasibility of binder jet additive manufacturing of a UHTC-TPMS structure by sintering and printing a null candidate. Components with a relative density of at least 92% theoretical, which were also a part of TPMS, were created.
The goal density denoted the transition from the intermediate to the final stage of sintering, which was needed for sintering of the complex near-net forms to full density using sinter-HIP technology and for inhibition of gas permeability. The purpose of the demonstration of the TPMS part was to see if the printing and sintering parameters derived from test coupons applied to the complex geometries that would be used in heat exchanger design.
The team printed 9 cm3 cubic TPMS pieces and sintered them without distorting or shattering them. Design topology, material, and manufacturing advances to achieve best-in-class performance in molten chloride salts in a CSP heat exchanger were proposed.
The researchers discussed the use of binder jet additive manufacturing paired with sintering to construct UHTC-TPMS cells based on ZrB2-MoSi2 with particle sizes. Because ZrB2-MoSi2 possesses favorable processing characteristics and qualities, it was intentionally chosen as a null candidate to demonstrate UHTC-TPMS heat exchanger viability until the optimal UHTC material for the application could be determined.
The prepared structure had a length of 1.25 cm and a wall thickness of 1.5 mm as its final unit size. The measured densities were 5.62–5.80 g/cm3, or 92–95% of theoretical densities. Two of the three samples had a higher density, 5.90-5.94 g/cm3, whereas one sample had a lower density of 5.65 g/cm3. Sintering three samples at 2000 ºC for 18 hours resulted in densities ranging from 5.65–5.94 g/cm3, which were 93–98% of the theoretical, whereas an increase in the time at 1900 ºC to 18 hours resulted in one sample with a density of 5.66 g/cm3. The majority of the particles were in the 1-5 μm range, with no particles larger than 7 μm.
Based on the Schwarz-D TPMS, ZrB2-MoSi2 composite components were sintered with isotropic shrinkage of up to 60% by volume, which resulted in densities of 92-96% theoretical. Compared to systems based on tubes or plates, a heat exchanger based on a TPMS provided the potential to boost power density. Using the attained scaffold dimensions, a UHTC heat exchanger based on the Schwarz-D TPMS with molten salt and supercritical carbon dioxide working fluids could achieve a power density of up to 50 MW/m3.
In conclusion, this study demonstrated that binder jet additive manufacturing can be used to print and sinter UHTC-TPMS structures. To effectively limit distortion, it was discovered that a spatial confinement strategy was required. It was able to employ traditional powder feedstocks with a d50 of about 2-3 m, which are the same sizes used in conventional UHTC processing. These materials were sintered to relative densities of 92-98% theoretical, which were high enough to prevent heat exchanger fluids from passing through the walls, separating the two domains and allowing hot isostatic pressing if a higher density is required.
The authors proposed combining developments in design, materials, and production for CSP heat exchangers in light of these promising results. They mentioned that the largest binder jet printer on the market for printing ceramics has the potential to print a one-piece heat exchanger with a capacity rating of up to 3 MW based on this power density.
More from AZoM: Considering the Behavior of Doped SrTiO3 Ceramics
Kelly, J. P., Finkenauer, L. R., Roy, P., et al. Binder Jet Additive Manufacturing of Ceramic Heat Exchangers for Concentrating Solar Power Applications with Thermal Energy Storage in Molten Chlorides. Additive Manufacturing 102937 (2022).
https://www.sciencedirect.com/science/article/abs/pii/S2214860422003335
Disclaimer: The views expressed here are those of the author expressed in their private capacity and do not necessarily represent the views of AZoM.com Limited T/A AZoNetwork the owner and operator of this website. This disclaimer forms part of the Terms and conditions of use of this website.
Surbhi Jain is a freelance Technical writer based in Delhi, India. She holds a Ph.D. in Physics from the University of Delhi and has participated in several scientific, cultural, and sports events. Her academic background is in Material Science research with a specialization in the development of optical devices and sensors. She has extensive experience in content writing, editing, experimental data analysis, and project management and has published 7 research papers in Scopus-indexed journals and filed 2 Indian patents based on her research work. She is passionate about reading, writing, research, and technology, and enjoys cooking, acting, gardening, and sports.
Please use one of the following formats to cite this article in your essay, paper or report:
Jain, Surbhi. (2022, June 03). Binder Jetting Ceramic Advanced Heat Exchangers. AZoM. Retrieved on June 16, 2022 from https://www.azom.com/news.aspx?newsID=59246.
Jain, Surbhi. "Binder Jetting Ceramic Advanced Heat Exchangers". AZoM. 16 June 2022. <https://www.azom.com/news.aspx?newsID=59246>.
Jain, Surbhi. "Binder Jetting Ceramic Advanced Heat Exchangers". AZoM. https://www.azom.com/news.aspx?newsID=59246. (accessed June 16, 2022).
Jain, Surbhi. 2022. Binder Jetting Ceramic Advanced Heat Exchangers. AZoM, viewed 16 June 2022, https://www.azom.com/news.aspx?newsID=59246.
Do you have a review, update or anything you would like to add to this news story?
In this interview, AZoM talks to Jeanette Madigan from Mai Dubai about their water analysis, services and how Metrohm instruments impact their work.
James Tour & Kevin Wyss
AZoM spoke with Professor James Tour and Ph.D. candidate Kevin Wyss from Rice University about their research that has looked at upcycling disused car parts into high-quality turbostratic graphene.
AZoM speaks with Professor Chris Howe about his research with cyanobacteria. These algae were able to power a microprocessor for an extended period of time in an exciting new breakthrough for natural energy production.
This product profile outlines the MAX-iR FTIR Gas Analyzer from Thermo Fisher Scientific.
Learn more about the JAM-5200EBM E-Beam Metal Additive Manufacturing System for 3D Printing.
This product profile outlines the features and benefits of the Contour X - 500 3D Optical Profilometer.
This article provides an end-of-life assessment of lithium-ion batteries, focusing on the recycling of an ever-growing amount of spent Li-Ion batteries in order to work toward a sustainable and circular approach to battery use and reuse.
Corrosion is the degradation of an alloy caused by its exposure to the environment. Corrosion deterioration of metallic alloys exposed to the atmosphere or other adverse conditions is prevented using a variety of techniques.
Due to the ever-increasing demand for energy, the demand for nuclear fuel has also increased, which has further created a significant increase in the requirement for post-irradiation examination (PIE) techniques.
AZoM.com - An AZoNetwork Site
Owned and operated by AZoNetwork, © 2000-2022